HobbyCNC PRO 4-Axis Kit

[et_pb_section fb_built=”1″ _builder_version=”3.15″ custom_margin=”0px||0px|” custom_padding=”0px||0px|”][et_pb_row custom_padding=”0px||0px|” custom_margin=”0px||0px|” _builder_version=”3.15″][et_pb_column type=”4_4″ _builder_version=”3.0.47″ parallax=”off” parallax_method=”on”][et_pb_text admin_label=”Features” _builder_version=”3.19″ custom_margin=”0px|||” custom_padding=”0px|||”]

• 4 Axis Unipolar Chopper control.
• Individual OR simultaneous control of 2/4 Phase Stepper Motors.
• Accepts 5, 6, or 8 wire stepper motors only. 4 wire types are not usable.
• 42VDC maximum input voltage, 12VDC minimum input voltage. 24VDC Minimum Recommended Voltage.  Power supplies above 42VDC are not recommended.
• 3.0 Amps Maximum per Phase, 500ma (.5A) minimum. Each axis adjustable throughout this range.
• 1/1, 1/2, 1/4, 1/8, and 1/16 Microstepping.
• Step and Direction Control.
• Idle Current Reduction (option) via pin 1 enable
• Built In Protection Circuit to help against blown chips on stepper motor short or open connections.
• 3.5″ by 6.75″ double sided with top silkscreen and thru plated holes and lead free solder PCB. (RoHS compliant).
• Power On Reset.
• On board voltage regulation for 5-volt logic with 24VDC cooling fan from motor power supply (fan not included)
• On board connections for home and limit switches with 10K pullup resistor provided to each. No need for a separate “break out” board.
• Minimum of components to make assembly fast and easy!
• Works with Step and Direction software such as LinuxCNC, DeskNC, TurboCNC, Mach3, etc
• RoHS Compliant
• Optional heatsink for motor current over 2 amps.
• Compare product features

[/et_pb_text][et_pb_divider color=”#0c71c3″ _builder_version=”3.15″ custom_margin=”2px||2px|” custom_padding=”0px||0px|”][/et_pb_divider][et_pb_text admin_label=”ComboKits” _builder_version=”3.19.1″]

Save time and upgrade to the COMBO Kit.

HobbyCNC PRO COMBO Kits include:

• HobbyCNC PRO Stepper Motor Driver Kit 3 or 4 axis
• Stepper motors in same quantity as driver board channels (sorry no mix of motor sizes)
• 14′ of 6 conductor stranded stepper motor hookup cable
• M-F Parallel port cable 6′ long

HobbyCNC Kits require PCB soldering skills

[/et_pb_text][/et_pb_column][/et_pb_row][/et_pb_section][et_pb_section fb_built=”1″ _builder_version=”3.19.1″ global_module=”7067″ saved_tabs=”all”][et_pb_row custom_padding=”0|0px|0|0px|false|false” _builder_version=”3.19.1″][et_pb_column type=”4_4″ _builder_version=”3.19.1″ parallax=”off” parallax_method=”on”][et_pb_divider color=”#0c71c3″ _builder_version=”3.15″ custom_margin=”2px||2px|” custom_padding=”0px||0px|”][/et_pb_divider][et_pb_text admin_label=”Pinout Table Header” _builder_version=”3.19.1″]

HobbyCNC PRO Parallel Port Pinouts

[/et_pb_text][/et_pb_column][/et_pb_row][et_pb_row custom_padding=”0|0px|0|0px|false|false” _builder_version=”3.19.1″][et_pb_column type=”1_2″ _builder_version=”3.19.1″ parallax=”off” parallax_method=”on”][et_pb_text admin_label=”Left Pinout Table” _builder_version=”3.19.1″]

[table id=10 /]

[/et_pb_text][/et_pb_column][et_pb_column type=”1_2″ _builder_version=”3.19.1″ parallax=”off” parallax_method=”on”][et_pb_text admin_label=”Right Pinout Table” _builder_version=”3.19.1″]

[table id=11 /]

[/et_pb_text][/et_pb_column][/et_pb_row][et_pb_row custom_padding=”0|0px|0|0px|false|false” _builder_version=”3.19.1″][et_pb_column type=”4_4″ _builder_version=”3.19.1″ parallax=”off” parallax_method=”on”][et_pb_text admin_label=”Pinout notes” _builder_version=”3.19.1″ text_font=”||||||||” text_font_size=”11px”]

*     Power Reduction can be enabled (Active High). Refer to the HobbyCNC PRO manual for details.
**   The actual function of these pins is determined in your CAM software.
*** Pins are made available via solder pads. Nothing is done to these lines on the PRO board. Straight from the D connector to the solder pads at P6.

[/et_pb_text][/et_pb_column][/et_pb_row][/et_pb_section]